Ecofloor Hard
Ecofloor Hard
Non – Metallic Floor Hardener
100% Trusted by our clients
No Paint Needed For Your Industrial Flooring
High resistance to abrasion
Reduces dusting
Intrinsic colouring
Improves resistance to impact
Improves resistance to oils and greases
Easy to apply, Ecofloor Hard is broadcast over the fresh slab
Saves Time and labor costs by eliminating the need for a granolithic screed.
Today Just: Ecofloor Hard Natural - Php 777.50
Grey - Php 925.28
Green - Php 1,597.59
Red - Php 776.30
Beige - Php 740.09
Brown - Php 937.66
Light Brown - Php 699.08
Hard Blue - Php 1,763.81
Hard Copper - Php 799.93
Hard Yellow - Php 1,053.52
Hard Sundance - Php 1,052.42
Trusted by our Clients
Ecofloor Hard Technical Data
Description
Ready to use, dry shake, non-metallic floor hardener. It is composed of cement and hard aggregates of mineral origin. The particles have been selected for their shape, grading, and high physical and mechanical quality.
Uses
Ecofloor Hard is used for superficial reinforcing of floor slabs and
screeds where Good abrasion resistance and reduced dusting is required.
It is suitable for floors subject to severe mechanical wear, such as
• Factories
• Warehouses
• Engineering workshops
• Parking lots
• Service Stations
• Quays
• Garages, etc.
Instruction for use
Base Concrete
The base concrete shall be Grade 25 or higher with an onsite slump of between 75 mm and 100 mm.
The base concrete shall be laid and compacted in accordance with good concrete practice with particular attention to bay edges and corners. Care should be taken to ensure that the slab is laid to obtain an accurate finish profile and that laitance build-up is minimum.
Application
Ecofloor Hard shall be broadcasted over the still fresh but stiff concrete and should be marked into bays to ensure even distribution of materials.
As bay edges are subjected to heavier impact and wear, additional treatment should be considered for these areas. Once the base concrete slab is leveled, sprinkle Ecofloor Hard along the edges and compact into the surface using a steel trowel. Use approximately 0.5 to 0.6 kg per linear meter over a width to 100 to 120 mm. Saw – cut control joints should also be treated in the same manner.
Timing for application is very crucial and the “readiness” of the concrete must be determined. A common rule-of-thumb practice is when light foot traffic leaves a 3-5 mm imprint. When Ecofloor Hard is applied too early, water from the concrete will be absorbed and this may affect the strength of the base concrete. On the other hand, if application is done too late, there will be insufficient moisture from the concrete to complete the hydration process of Ecofloor Hard. As a result, the floor may “craze and pit”.
Ecofloor Hard is applied in two stages. Use 60% of the specified dosage in the first application and broadcast evenly over the marked area. Once the materials is uniformly moistened, compact, the floor with a low speed mechanical trowel. When it is completed, the remaining 40% of the materials is immediately broadcasted over the floor at a direction perpendicular to the first application. The floor is compacted again using a mechanical trowel when the Ecofloor Hard is uniformly moistened. Precaution must be taken to ensure that the floor is not overworked.
Curing
The Ecofloor hard surface must be protected to prevent rapid water loss which may result in surface cracks. Immediately after leveling, spray Ecocure WS Curing Compound over the floor at a rate of 0.2 liters per m2.
Waiting Time
Depending on the ambient temperature and the type of cement used in the base concrete, the pre-usage waiting time is
24 to 48 hours for foot Traffic
7 to 10 days for light traffic, and
28 days for normal traffic
Technical Data
Form
Powder
Naturals
Natural / Gray / Green / Red / Brown / Beige
Average Consumption
4-6 kg Ecofloor Hard per sq. meter, yielding a 2-3 mm strengthened coat.
Ph Value
Approx. 12
Storage
Store in dry place
Shelf Life
12 months when unopened
Packaging
25 Kg / Bag